Perle Systems IOLAN CSS Manual de usuario Pagina 113
- Pagina / 164
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Network Commands 109
Logging Commands
Logging Commands
Set Syslog
Show Syslog
Description Configures the system log.
User Level Admin
Syntax
set syslog
[level emergency|alert|critical|error|warning|notice|info|debug]
[primary-host <config_host>] [secondary-host <config_host>]
Options level
Choose the event level that triggers a syslog entry:
z Emergency
z Alert
z Critical
z Error
z Warning
z Notice
z Info
z Debug
When you select a
Level, all the levels that appear above it in the list also trigger a
syslog entry. For example, if you select
Error, all Error, Critical, Alert, and Emergency
events will be logged.
primary-host
The first preconfigured host that the IOLAN will attempt to send system log messages
to; messages will be displayed on the host’s monitor.
secondary-host
If the IOLAN cannot communicate with the primary host, then the IOLAN will attempt
to send system log messages to this preconfigured host; messages will be displayed on
the host’s monitor.
Description Shows the syslog settings.
User Level Admin
Syntax
show syslog
- SDS/SCS/STS 1
- Command Line Interface 1
- Reference Guide 1
- Table of Contents 3
- About This Book 15
- Intended Audience 15
- Contacting Technical Support 16
- Repair Procedure 17
- Feedback on this Manual 17
- Introduction Chapter 1 19
- Command Shortcuts 20
- Command Options 20
- Server Commands Chapter 2 21
- Set Port-Buffering 22
- Set Server 23
- Set SSL Server 26
- Set Service 27
- Show Console 28
- Show Custom-App 28
- Show Port-Buffering 28
- Hardware Commands 29
- SSH Server Commands 29
- Show SSH-Server 30
- SSL/TLS Commands 31
- Set SSL Server Cipher-suite 32
- Modbus Commands 33
- Show Modbus 34
- Authentication Commands 35
- Set Authentication LDAP 36
- Set Authentication Kerberos 36
- Set Authentication NIS 37
- Add RADIUS 37
- Delete RADIUS 37
- Set Authentication RADIUS 38
- Set Authentication TACACS+ 39
- Set Authentication SecurID 39
- TruePort Baud Commands 40
- Email Commands 41
- Clustering Commands 42
- Set Clustering Slave-IP 43
- Show Clustering Slave-IP 43
- Dynamic DNS Commands 44
- Server Commands 45 45
- PCI Commands 47
- Set PCI Wireless-WAN 48
- Show Wireless-WAN 48
- IPv6 Commands 49
- Add Custom-IPv6 50
- Set Custom-IPv6 51
- Delete Custom-IPv6 51
- IPv6 Router Advertisements 52
- User Commands Chapter 3 53
- Set Termtype 55
- Set User 55
- Set User Session 56
- Show Line Users 57
- Syslog Console 58
- Show Sessions 58
- Show Termtype 58
- Configuring Users 60
- Set Default User 61
- Show Default User 68
- Show User 68
- Line Commands Chapter 4 69
- Line Commands 71 73
- Line Commands 73
- Set Line Interface 74
- Set Line Service 75
- Line Commands 75 77
- Set Modem 78
- Show Line 78
- Line Service Commands 79
- Set SSH-Client 80
- Line Commands 79 81
- Name and Password values 81
- Auto Login is enabled 81
- Set PPP Dynamic-DNS 86
- Set SLIP 86
- Set Vmodem 88
- Line Commands 87 89
- NO CARRIER will be sent 89
- CONNECT 9600 90
- Set Vmodem-Phone 91
- Set SSL Line 91
- Set SSL Line Cipher-suite 93
- Set Modbus-Slave Line 94
- Set Modbus-Master Line 94
- Set Power-Management Line 95
- Set Multihost Line 96
- Set Line Initiate-Connection 96
- Show Interface 96
- Show Power-Management 96
- Modem Commands 98
- Packet Forwarding Commands 100
- Line Commands 99 101
- Transmit Timer 101
- Show Packet-Forwarding Line 103
- Network Commands Chapter 5 105
- Delete Trap 106
- Set SNMP 106
- Delete Community 106
- Set SNMP V3-Security 107
- TFTP Commands 108
- Hosts Commands 108
- DNS/WINS Commands 109
- Delete DNS 110
- Delete WINS 110
- Show DNS 110
- Show Server 110
- Show WINS 110
- Gateway Commands 111
- Delete Gateway 112
- Set Gateway 112
- Show Gateways 112
- Logging Commands 113
- RIP Commands 114
- Show RIP 115
- IPsec Commands 116
- IPv6 Tunnels 119
- Set IPv6tunnel 120
- Show IPv6tunnel 120
- Delete IPv6tunnel 120
- L2TP/IPsec 121
- Default Gateway value (if no 122
- VPN Exceptions 123
- Delete VPN Exception 124
- Show VPN Exception 124
- Time Commands Chapter 6 125
- SNTP Commands 126
- Time/Date Setting Commands 127
- Set Summertime Fixed 128
- Set Summertime Recurring 128
- Show Date 129
- Show Summertime 129
- Administration 131
- Commands Chapter 7 131
- TFTP File Transfer Commands 132
- Custom Factory Default 134
- MOTD Commands 137
- Statistics Commands Chapter 8 139
- Run-Time Statistics 140
- IOLAN+ User 141
- Commands Chapter 9 141
- I/O Commands Chapter 10 143
- Set Line 144
- Set IOChannel 145
- Set IOChannel Digital Input 146
- Set IOChannel Digital Output 148
- Set IOChannel Relay 150
- Set IOChannel IOExtension 154
- I/O Commands 149 155
- Set IOChannel Multihost 156
- Set IOChannel IOExtension SSL 157
- Show IOChannel Status 157
- Kill IOChannel 157
- I/O Channel Control Commands 158
- Digital Input 159
- Analog Input 159
- Calibrate Analog 159
- Reset Calibration 159
- Power Commands Chapter 11 161
- Power Commands 162
- Glossary 163
© 2020, manymanuals.es. Todos los derechos reservados | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales