Perle Systems IOLAN MDC Manual de usuario Pagina 114
- Pagina / 162
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
IPsec Commands
114 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, Version 3.7
Show RIP Peers
IPsec Commands
Once there is an active VPN tunnel, the IOLAN expects all connections to be established through a
VPN tunnel. To allows hosts to connect outside of the VPN tunnel, you must configure VPN
exceptions, see
VPN Exceptions on page 121 for the command syntax.
Add IPsec
Set IPsec
Description Shows current information about IPv4 or IPv6 RIP peers.
User Level Normal, Admin
Syntax
show rip peers [ipv6]
Description Adds an IPsec tunnel.
User Level Admin
Syntax
add ipsec <tunnel_name>
Option <tunnel_name>
The name of an IPsec VPN tunnel. You can configure up to 64 VPN tunnels.
Description Configures the IPsec tunnel.
User Level Admin
Syntax
set ipsec <config_tunnel_name>
[authentication-method shared-secret|rsa-signature|x.509-certificate]
[boot-action start|add|ignore] [local-device left|right]
[
local-external-ip-address <IPv4/IPv6_address/FQDN>]
[local-host-network <IPv4_addr> <subnet_mask>|
<IPv6_address> <prefix_bits>
]
[local-ip-address <
IPv4/IPv6_address/FQDN>]
[local-next-hop <IPv4/IPv6_address>]
[remote-external-ip-address <IPv4/IPv6_address/FQDN>]
[remote-host-network
<IPv4_addr> <subnet_mask>|
<IPv6_address> <prefix_bits>
]
[remote-ip-address <IPv4/IPv6_address/FQDN>]
[remote-next-hop <
IPv4/IPv6_address>]
[remote-validation-criteria
country <code>|state-province <text>|locality <text>
|organisation <text>|organisation-unit <text>
|common-name <text>|email <email_addr>]
set ipsec <config_tunnel_name> secret <text>
set ipsec use-nat-traversal enabled|disabled
- SDS/SCS/STS/MDC 1
- Command Line Interface 1
- Reference Guide 1
- Table of Contents 3
- About This Book 13
- Intended Audience 13
- Contacting Technical Support 14
- Repair Procedure 15
- Feedback on this Manual 15
- Introduction Chapter 1 17
- Command Shortcuts 18
- Command Options 18
- Server Commands Chapter 2 19
- Set Port-Buffering 20
- Set Server 21
- Set SSL Server 24
- Set Service 25
- Show Console 26
- Show Custom-App 26
- Show Port-Buffering 26
- Hardware Commands 27
- SSH Server Commands 27
- Show SSH-Server 28
- SSL/TLS Commands 29
- Set SSL Server Cipher-suite 30
- Modbus Commands 31
- Show Modbus 32
- Authentication Commands 33
- Set Authentication Kerberos 34
- Set Authentication LDAP 34
- Set Authentication NIS 35
- Add RADIUS 35
- Delete RADIUS 35
- Set Authentication RADIUS 36
- Set Authentication TACACS+ 37
- Set Authentication SecurID 37
- TruePort Baud Commands 38
- Email Commands 39
- Clustering Commands 40
- Set Clustering Slave-IP 41
- Show Clustering Slave-IP 41
- Dynamic DNS Commands 42
- Server Commands 43 43
- PCI Commands 45
- Set PCI Wireless-WAN 46
- Show Wireless-WAN 46
- IPv6 Commands 47
- Add Custom-IPv6 48
- Set Custom-IPv6 49
- Delete Custom-IPv6 49
- IPv6 Router Advertisements 50
- User Commands Chapter 3 51
- Set Termtype 53
- Set User 53
- Set User Session 54
- Show Line Users 55
- Syslog Console 56
- Show Sessions 56
- Show Termtype 56
- Configuring Users 58
- Set Default User 59
- Show Default User 66
- Show User 66
- Line Commands Chapter 4 67
- Line Commands 71 71
- Line Commands 71
- Set Line Interface 72
- Set Line Service 73
- Line Commands 75 75
- Set Modem 76
- Show Line 77
- Line Service Commands 78
- Set SSH-Client 79
- Name and Password values 80
- Auto Login is enabled 80
- Set PPP Dynamic-DNS 85
- Set SLIP 85
- Set Vmodem 87
- NO CARRIER will be sent 88
- Line Commands 89 89
- CONNECT 9600 89
- Set Vmodem-Phone 90
- Set SSL Line 90
- Line Commands 91 91
- Set SSL Line Cipher-suite 92
- Set Modbus-Slave Line 93
- Set Modbus-Master Line 93
- Set Power-Management Line 94
- Set Multihost Line 95
- Set Line Initiate-Connection 95
- Show Interface 95
- Show Power-Management 95
- Modem Commands 97
- Packet Forwarding Commands 100
- Line Commands 101 101
- Show Packet-Forwarding Line 102
- Network Commands Chapter 5 103
- Set SNMP 104
- Delete Community 104
- Delete Trap 104
- Set SNMP V3-Security 105
- TFTP Commands 106
- Hosts Commands 106
- DNS/WINS Commands 107
- Delete DNS 108
- Delete WINS 108
- Show DNS 108
- Show Server 108
- Show WINS 108
- Gateway Commands 109
- Delete Gateway 110
- Set Gateway 110
- Show Gateways 110
- Logging Commands 111
- RIP Commands 112
- Show RIP 113
- IPsec Commands 114
- IPv6 Tunnels 117
- Set IPv6tunnel 118
- Show IPv6tunnel 118
- Delete IPv6tunnel 118
- L2TP/IPsec 119
- Default Gateway value (if no 120
- VPN Exceptions 121
- Delete VPN Exception 122
- Show VPN Exception 122
- Time Commands Chapter 6 123
- SNTP Commands 124
- Time/Date Setting Commands 125
- Set Summertime Fixed 126
- Set Summertime Recurring 126
- Show Date 127
- Show Summertime 127
- Administration 129
- Commands Chapter 7 129
- TFTP File Transfer Commands 130
- Custom Factory Default 132
- MOTD Commands 135
- Statistics Commands Chapter 8 137
- Run-Time Statistics 138
- IOLAN+ User 139
- Commands Chapter 9 139
- I/O Commands Chapter 10 141
- Set Line 142
- Set IOChannel 143
- Set IOChannel Digital Input 144
- Set IOChannel Digital Output 146
- Set IOChannel Relay 148
- Set IOChannel IOExtension 152
- I/O Commands 153 153
- Set IOChannel Multihost 154
- Set IOChannel IOExtension SSL 155
- Show IOChannel Status 155
- Kill IOChannel 155
- I/O Channel Control Commands 156
- Digital Input 157
- Analog Input 157
- Calibrate Analog 157
- Reset Calibration 157
- Power Commands Chapter 11 159
- Power Commands 160
- Glossary 161
Relacionado con productos y manuales para Gateways / Controladores Perle Systems IOLAN MDC
(164 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales