Perle Systems IOLAN MDC Manual de usuario Pagina 75
- Pagina / 162
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Line Commands 75
Line Commands
rlogin
Sets the line for a remote login connection.
raw
Creates a connection where no authentication takes place and data is passed unchanged.
telnet
Sets the line for a telnet connection.
ssh
Sets the line for an SSH connection.
reverse
Enables a TCP/IP host to establish a login connection on an external machine attached
to a port. For example, to access machines like protocol converters, statistical
multiplexors, or machines like routers, firewalls, servers, etc.
client-tunnel
Sets the line for a client tunnel connection.
dslogin
The default connection. The IOLAN displays a login on that line. For example,
DSLogin is used when a System Administrator configures the IOLAN, providing
authentication of a user before starting a
User Service of SLIP, or users starts a
session(s) from the IOLAN to hosts.
printer
Using the IOLAN as a printer server. For example, remote printing using LPD (port
515) or RCP (port 514).
ppp
Sets the port to a dedicated PPP line.
slip
Sets the port in SLIP mode.
udp
Sets the line to listen for and/or send UDP data.
vmodem
The IOLAN port behaves as if it were a modem to the attached device.
server-tunnel
Sets the line for a server tunnel connection.
modbus-master
Sets the line to act as a Modbus master.
custom-app
Sets the line to use the custom application created with the SDK.
power-management
Indicates that there is a power bar connection to this serial line.
trueport
Sets the line to communicate with the TruePort utility. You must install the TruePort
utility on the host machine.
- SDS/SCS/STS/MDC 1
- Command Line Interface 1
- Reference Guide 1
- Table of Contents 3
- About This Book 13
- Intended Audience 13
- Contacting Technical Support 14
- Repair Procedure 15
- Feedback on this Manual 15
- Introduction Chapter 1 17
- Command Shortcuts 18
- Command Options 18
- Server Commands Chapter 2 19
- Set Port-Buffering 20
- Set Server 21
- Set SSL Server 24
- Set Service 25
- Show Console 26
- Show Custom-App 26
- Show Port-Buffering 26
- Hardware Commands 27
- SSH Server Commands 27
- Show SSH-Server 28
- SSL/TLS Commands 29
- Set SSL Server Cipher-suite 30
- Modbus Commands 31
- Show Modbus 32
- Authentication Commands 33
- Set Authentication Kerberos 34
- Set Authentication LDAP 34
- Set Authentication NIS 35
- Add RADIUS 35
- Delete RADIUS 35
- Set Authentication RADIUS 36
- Set Authentication TACACS+ 37
- Set Authentication SecurID 37
- TruePort Baud Commands 38
- Email Commands 39
- Clustering Commands 40
- Set Clustering Slave-IP 41
- Show Clustering Slave-IP 41
- Dynamic DNS Commands 42
- Server Commands 43 43
- PCI Commands 45
- Set PCI Wireless-WAN 46
- Show Wireless-WAN 46
- IPv6 Commands 47
- Add Custom-IPv6 48
- Set Custom-IPv6 49
- Delete Custom-IPv6 49
- IPv6 Router Advertisements 50
- User Commands Chapter 3 51
- Set Termtype 53
- Set User 53
- Set User Session 54
- Show Line Users 55
- Syslog Console 56
- Show Sessions 56
- Show Termtype 56
- Configuring Users 58
- Set Default User 59
- Show Default User 66
- Show User 66
- Line Commands Chapter 4 67
- Line Commands 71 71
- Line Commands 71
- Set Line Interface 72
- Set Line Service 73
- Line Commands 75 75
- Set Modem 76
- Show Line 77
- Line Service Commands 78
- Set SSH-Client 79
- Name and Password values 80
- Auto Login is enabled 80
- Set PPP Dynamic-DNS 85
- Set SLIP 85
- Set Vmodem 87
- NO CARRIER will be sent 88
- Line Commands 89 89
- CONNECT 9600 89
- Set Vmodem-Phone 90
- Set SSL Line 90
- Line Commands 91 91
- Set SSL Line Cipher-suite 92
- Set Modbus-Slave Line 93
- Set Modbus-Master Line 93
- Set Power-Management Line 94
- Set Multihost Line 95
- Set Line Initiate-Connection 95
- Show Interface 95
- Show Power-Management 95
- Modem Commands 97
- Packet Forwarding Commands 100
- Line Commands 101 101
- Show Packet-Forwarding Line 102
- Network Commands Chapter 5 103
- Set SNMP 104
- Delete Community 104
- Delete Trap 104
- Set SNMP V3-Security 105
- TFTP Commands 106
- Hosts Commands 106
- DNS/WINS Commands 107
- Delete DNS 108
- Delete WINS 108
- Show DNS 108
- Show Server 108
- Show WINS 108
- Gateway Commands 109
- Delete Gateway 110
- Set Gateway 110
- Show Gateways 110
- Logging Commands 111
- RIP Commands 112
- Show RIP 113
- IPsec Commands 114
- IPv6 Tunnels 117
- Set IPv6tunnel 118
- Show IPv6tunnel 118
- Delete IPv6tunnel 118
- L2TP/IPsec 119
- Default Gateway value (if no 120
- VPN Exceptions 121
- Delete VPN Exception 122
- Show VPN Exception 122
- Time Commands Chapter 6 123
- SNTP Commands 124
- Time/Date Setting Commands 125
- Set Summertime Fixed 126
- Set Summertime Recurring 126
- Show Date 127
- Show Summertime 127
- Administration 129
- Commands Chapter 7 129
- TFTP File Transfer Commands 130
- Custom Factory Default 132
- MOTD Commands 135
- Statistics Commands Chapter 8 137
- Run-Time Statistics 138
- IOLAN+ User 139
- Commands Chapter 9 139
- I/O Commands Chapter 10 141
- Set Line 142
- Set IOChannel 143
- Set IOChannel Digital Input 144
- Set IOChannel Digital Output 146
- Set IOChannel Relay 148
- Set IOChannel IOExtension 152
- I/O Commands 153 153
- Set IOChannel Multihost 154
- Set IOChannel IOExtension SSL 155
- Show IOChannel Status 155
- Kill IOChannel 155
- I/O Channel Control Commands 156
- Digital Input 157
- Analog Input 157
- Calibrate Analog 157
- Reset Calibration 157
- Power Commands Chapter 11 159
- Power Commands 160
- Glossary 161
Relacionado con productos y manuales para Gateways / Controladores Perle Systems IOLAN MDC
(164 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales